Waterproof Irrigation Wire Connectors

Whether you’re installing landscape lighting or irrigation equipment, reliable and durable connections are essential. Unlike tape, wire connectors are moisture-resistant and protect exposed wiring from corrosion.

Waterproof irrigation wire connectors are filled with moisture-resistant silicone, grease or petroleum and help prevent the onset of corrosion on exposed electrical wiring. These products are ideal for any setup that’s exposed to moisture and outdoor elements.

DryConn Blue/Blue Wire Connectors

King Innovation Blue Waterproof Connectors eliminate and connect loose wires to prevent electrical fires and system failure. They are corrosion and water proof in design, making them perfect for landscape lighting applications. These connectors can be used with low voltage building or sign wire up to 600V and are made of a durable plastic that is UL listed for landscape lighting and underground conduit. One step installation. No waterproof irrigation wire connectors pre-twisting required. Silicone seal fills and protects raw copper connection from ground moisture. Available in (2) pack or (12) pack.

Waterproof your outdoor splices with this quality one-step connector, filled with a dielectric silicone sealant that surrounds splices and makes them waterproof and corrosion resistant. It meets the conditions set by the most recent NEC code book requiring a UL listed connector be used for all splices in wet and damp locations.

Blazing SnapLoc Wire Connectors

Professional irrigation and landscape lighting contractors know that a good connection is the most important part of an efficient system. Yet traditional twist-on connectors regularly fall short, causing the sprinkler to fail or creating a dangerously open connection to water, dirt and debris. Worse, they often dangle off the ends of the wires or overtwist, which causes the silicone inside to break off and expose your wiring to moisture and corrosion.

Blazing SnapLoc solves these problems with a patented design that’s safe, fast and easy to use in direct bury applications. Designed to be used with two wires, this waterproof and corrosion-proof connector features a latch snap that holds the wire tightly for maximum wire grip. Each snap-lock connection comes prefilled with dielectric silicone sealant that never hardens.

To install, simply rotate the wings apart, insert unstripped wires, and then close the handle. The waterproof silicone sealant inside hydraulically pumps out to completely encapsulate the bare wires, closing all entryways against moisture and protecting the connections from damage and corrosion. A double O-ring bars water from creeping in and the connector is vibration-proof, so it’s ideal for outdoor applications.

Blazing LV 9000 Wire Connectors

Blazing LV 9000 wire connectors are ideal for irrigation valve splices waterproof light socket and other residential and commercial sprinkler system connections, landscape lighting, and golf course wiring. They hold up to 5 #18 wires in a patented V-channel that locks in the pre-filled silicone outer housing. The inner sleeve also features a double O-ring seal to prevent water creeping in.

Unlike twist-on connectors that often dangle off the ends of the wires, these insulators hydraulically pump and pack waterproof silicone around each splice. This re-closes all entryways against moisture, corrosion and electrical shorts. The connectors are vibration proof and won’t dangle off the ends of the wires.

Strip the wires 3/4″ and group together. Insert bare wire ends into either side of the “V” channel. Press and firmly snap down locking ring to close. Slide inner sleeve up over the outer sleeve until both are double locked. LV 9000 Connectors can be used with both solid and stranded wires.

Blazing BVS-1 Wire Connectors

Made specifically for irrigation (BVS) and landscape lighting (BLS) applications, this waterproof and corrosion-proof connector saves money and time with a one-step installation that eliminates the need for stripping or twisting. Simply rotate the wings apart and insert unstripped wire ends, then close by rotating the handles together. A latch snap holds the connections tightly for maximum moisture protection and wire restraint. Each connection is prefilled with dielectric silicone sealant that never hardens. The BVS-1 is UL listed for raintight and watertight connections in direct bury applications. Rated up to 30V building wire. Made in USA. Lifetime warranty. CSA Certified.